LG dryers are equipped with error codes to provide users with valuable diagnostic information when problems arise. These alphanumeric codes help identify specific issues, enabling users to troubleshoot and fix their dryers efficiently. In this guide, we will explore common LG dryer error codes, providing step-by-step instructions for resolving each one.
Table of Contents
LG Dryer Error Codes
LG dryers are equipped with error codes to assist users in troubleshooting potential issues. One common reason for these error codes is restricted airflow or drying conditions, which can cause problems such as D80, D90, D95, CL errors Etc..
D80 Error
When your LG dryer displays the D80 error code, it indicates that the dryer’s air exhaust vent system is restricted. Follow these steps to fix it:
How To Fix?
1. Check the lint filter: Remove and clean the lint filter thoroughly by removing any built-up lint or debris.
2. Inspect the vent system: Make sure the venting system and ductwork are clear of obstructions and properly connected.
3. Ensure proper airflow: Confirm that the exterior exhaust vent cap is not blocked by lint or other objects.
4. Verify adequacy of airflow: If necessary, use a vacuum cleaner or brush to remove any accumulated lint from the vent hose and exhaust duct.
D90 Error
The D90 error code on your LG dryer indicates restricted airflow due to fewer wrinkles settings being selected. Here’s how you can resolve this issue:
How To Fix?
1. Change cycle selection: Adjust the drying cycle settings to include a higher temperature option instead of lower wrinkle settings.
2. Check vents and hoses: Inspect the venting system and hoses for blockages or restrictions that prohibit proper airflow.
3. Clean lint filter and ducts: Remove excess lint from both the lint filter and all accessible areas of the ductwork using a vacuum cleaner or cleaning brush.
D95 Error
An LG dryer displaying the D95 error signifies poor drying performance resulting from restricted ventilation airflow. Fixing this issue involves taking specific steps:
How To Fix?
1. Check exterior ventilation hood: Ensure that there are no objects blocking or obstructing the exterior ventilation hood where moist air exits.
2. Clear lint filter: Remove and clean the lint filter thoroughly by eliminating any lint or debris buildup.
3. Inspect exhaust ductwork: Examine the exhaust ductwork for blockages, including excess lint or crimping that might restrict airflow.
4. Ventilate the area: Ensure there is adequate ventilation around the dryer to prevent overheating and improve drying performance.
CL Error
When your LG dryer shows a CL error code, it indicates that the control panel has been locked. Follow these straightforward steps to unlock it:
How To Fix?
1. Press and hold “Start/Pause” button: Hold down this button for five seconds to deactivate the control lock feature.
2. Check for child lock function: Review the user manual or consult LG’s website to verify if your model includes a child lock function that needs disengaging.
3. Power cycle the dryer: If unlocking doesn’t resolve the issue, try turning off and unplugging the dryer for a few minutes before plugging it back in and restarting it.
4. Contact LG customer support: If none of these steps resolve the CL error, contact LG’s customer support for further assistance or professional service.
NP Error
When your LG dryer displays the NP error code, it indicates a problem with the power supply or electrical connection. Follow these steps to fix it:
How To Fix?
1. Check power source: Ensure that the dryer is properly plugged into a functioning power outlet.
2. Reset circuit breaker: If the dryer isn’t receiving power, check the circuit breaker panel and reset any tripped breakers.
3. Inspect power cord: Verify that the power cord is securely connected to both the dryer and the outlet.
4. Test voltage levels: Use a multimeter to check if there is adequate voltage reaching the dryer.
TE1 Error
The TE1 error code on your LG dryer suggests an issue with the thermistor or temperature sensor. Here’s how you can resolve this problem:
How To Fix?
1. Unplug dryer: Disconnect the dryer from its power source before proceeding.
2. Locate thermistor: The thermistor is usually located near the dryer’s heating element assembly.
3. Test resistance: Use a multimeter set to ohms to measure the resistance of the thermistor. Compare it to manufacturer specifications. Replace if necessary.
4. Reassemble and test: Once you’ve replaced or fixed any faulty parts, reassemble the dryer and plug it in, then run a test cycle to ensure proper functioning.
LE1 Error
An LG dryer displaying the LE1 error indicates an issue with its motor or motor control board. Fixing this issue involves taking specific steps:
How To Fix?
1. Disconnect power supply: Unplug your dryer from its power source for safety purposes.
2. Inspect drive belt: Check if the drive belt is intact and properly placed on the drum and motor pulley. Replace the belt if it appears worn or damaged.
3. Examine motor components: Inspect the motor wiring, connectors, and control board for any loose connections or signs of damage. Tighten or replace as necessary.
4. Test motor: Use a multimeter to test the motor for continuity and proper functioning. Replace the motor or control board if needed.
P5 Error
The P5 error code on your LG dryer indicates a problem with its inlet thermistor or temperature sensor. Follow these steps to fix it:
How To Fix?
1. Unplug dryer: Disconnect the dryer from its power source before proceeding.
2. Locate inlet thermistor: The inlet thermistor is usually located near the dryer’s inlet valve assembly.
3. Test resistance: Use a multimeter set to ohms to measure the resistance of the inlet thermistor. Compare it to manufacturer specifications. Replace if necessary.
4. Reassemble and test: Once you’ve replaced or fixed any faulty parts, reassemble the dryer and plug it in, then run a test cycle to ensure proper functioning.
Frequently Asked Questions:
What is the HS code on my LG dryer?
The HS code, also known as the Harmonized System code, is a standardized international code used for classifying and identifying products. While each product has its own unique HS code, it is generally not applicable to individual consumer appliances such as an LG dryer. HS codes are typically used for customs purposes during import and export processes.
What is the tE2 code on my LG dryer?
If you see the tE2 error code on your LG dryer, it indicates a thermistor error. The thermistor is a component that measures temperature. To resolve this issue, you should first check if the thermistor is properly connected and free from any damage or corrosion. If necessary, replace the thermistor with a new one compatible with your model. Once replaced, run a test cycle to ensure the error has been resolved.
What does te3 mean on LG dryer?
The te3 error code on an LG dryer indicates an issue with the exhaust duct blockage detection system. This error occurs when there is restricted airflow due to lint buildup or obstructions in the exhaust duct. To remedy this problem, thoroughly clean out the exhaust vent and remove any lint or debris that may be blocking it. Additionally, ensure that the exhaust duct is properly connected and not kinked. After making these adjustments, reset the dryer by unplugging it from the power source for a few minutes before plugging it back in.
How do I reset my LG dryer?
To reset your LG dryer, follow these simple steps:
1. Make sure that the dryer is turned off and disconnected from its power source.
2. Wait for approximately 5 minutes to allow any residual power to dissipate.
3. Plug in the appliance back into its power source.
4. Turn on your LG dryer.
5. Check if any error codes are still displaying on the control panel.
6. If no error codes appear, the reset was successful, and your dryer should function normally. If errors persist, consult the user manual or contact LG customer support for further assistance.
Conclusion
Understanding and effectively addressing LG dryer error codes is essential for maintaining optimal dryer performance. By following the step-by-step guides provided in this comprehensive guide, you can easily troubleshoot and resolve common error codes like.
By applying these techniques and guidelines, you can confidently tackle LG dryer error codes with ease. Remember to consult your dryer’s user manual or contact LG support if you encounter any difficulties outside of the specified error codes covered in this guide.
-
Jeffrey M. Cooks
Jeffrey M. Cooks is the knowledgeable author behind the LG dryer on dryercodes.com. With a deep understanding of LG dryer codes, his contributions offer valuable insights and practical advice to assist users in effectively managing LG appliance issues. Jeffrey's expertise in diagnosing and resolving complex problems has positioned him as a trusted resource for individuals seeking reliable information to maintain and optimize their LG dryers. Through his dedicated contributions, Jeffrey consistently enhances the understanding and capabilities of users by providing informed approaches to improve the performance of their LG appliances.
View all posts
